LED Tape Light

LED tape light sold as a complete system: tape, drivers, and channel sized together across 12V and 24V lines, with free shipping on every order. The guidance below the products walks wattage per foot classes, max run lengths, and driver sizing math that applies across every brand we carry.

Products List

Sort By:

Display Type:
Filters
  • Product
  • Qty in Cart
  • Quantity
  • Price
  • Subtotal
  • Total: items /

Adding your products to cart

View Cart Continue Shopping

LED Tape Light Planning Guide

Run Length and Driver Sizing for LED Tape Lighting

Two numbers prevent nearly every tape lighting failure. The first is maximum run length: 12V tape typically runs to about 16 ft from a single feed before voltage drop dims the far end, while 24V tape roughly doubles that to about 32 ft. Longer layouts are fed from both ends or split into multiple home runs. The second is driver capacity: multiply watts per foot by total footage, then size the driver with 20 percent headroom. A 20 ft run of 5 W/ft tape draws 100W, so specify at least a 120W driver. Undersized drivers run hot and fail early; the 1.2 multiplier is the cheapest insurance in the category. Matching LED Drivers are stocked alongside the tape so the system ships as a system.

Dimming: TRIAC, ELV, and 0-10V

Dimming behavior is set by the driver, not the tape, and mismatches are the top source of flicker complaints. TRIAC (forward phase) dimmable drivers work with the incandescent-style dimmers already in most homes and small offices. ELV (reverse phase) drivers cost more but dim more smoothly at the bottom of the range, which matters in coves and bedrooms. Commercial control systems standardize on 0-10V, the same low voltage control wiring used across commercial fixtures. Confirm the dimmer, driver, and control protocol agree before ordering, and use an LED-rated dimmer with a compatible minimum load.

Tape Light or Strip Light Fixtures

The names get used interchangeably, but at QuickShipLights they are different products. Tape light is the flexible adhesive-backed ribbon on this page, cuttable to length and powered through a remote driver. LED Strip Lights are rigid, line voltage linear fixtures for garages, shops, and utility spaces. If the job needs to follow a curve, tuck into millwork, or disappear into a cove, you are on the right page.

Build the full system from the subcategories: 12V LED Tape for shorter runs and retrofits, 24V LED Tape for longer commercial runs, and Tape Light Accessories for aluminum channel, lenses, connectors, and end caps. Channel is not cosmetic: it heat-sinks the tape, extends its life, and turns a bare ribbon into a finished linear fixture. Kitchen and millwork projects can also cross-shop Undercabinet Lighting. Ordering tape, driver, and channel together means the pieces arrive together; stock status and lead times are shown on each product page.

LED Tape Light Sized as a System, Not a Reel

Every top-ranking LED tape light page belongs to a single manufacturer, which means none of them can tell you how their tape compares to anyone else's. A distributor can. This page treats tape light the way an installer has to: as a three-part system of tape, driver, and channel that must be sized together, with the same math applying across every brand we carry. Get the wattage class and run length right and the rest of the project is assembly.

Wattage Classes Across Brands

ClassWatts Per FootTypical OutputWhere It Belongs
Accent1.5 to 3 W/ft100 to 250 lm/ftCoves, toe kicks, indirect ceiling details
Task4 to 6 W/ft300 to 500 lm/ftUndercabinet task lighting, shelving, closets
High output7 to 10 plus W/ft500 to 900 lm/ftDisplay cases, retail millwork, sign backlighting, primary cove lighting

Frequently Asked Questions About LED Tape Lighting

Multiply the tape's watts per foot by the total footage, then add 20 percent headroom. A 15 ft run of 4.4 W/ft tape draws 66W, so specify at least an 80W driver. Running a driver at its maximum rating shortens its life, and the driver is usually the first component to fail in a tape system, so the headroom rule pays for itself.

From a single feed point, 12V tape typically runs to about 16 ft before voltage drop visibly dims the far end, and 24V tape to about 32 ft. Exact limits vary by wattage class and manufacturer, so check the spec sheet. For longer layouts, feed the run from both ends or break it into multiple home runs back to the driver.

Use 24V for most commercial work and any run past 16 ft; it carries half the current of 12V at the same wattage, which means less voltage drop and longer clean runs. Use 12V for short accent runs and when extending an existing 12V system where the transformer and wiring are already in place. The two voltages are not interchangeable on one driver.

Yes. Tape light is designed to be cut at marked cut points, typically every 1 to 3 inches depending on the series and voltage. Cut only on the marked line, then finish the cut end with a compatible connector or solder joint and an end cap. Cutting between cut points kills the last segment of LEDs, so measure against the cut interval before trimming.

It can be, if the driver is TRIAC (forward phase) dimmable and the wall dimmer is LED rated. The tape itself does not determine dimming; the driver does. For smoother low-end performance choose an ELV driver with an ELV dimmer, and for commercial control systems specify a 0-10V dimmable driver. Mismatched dimmer and driver protocols are the most common cause of flicker.

IP20 tape is for dry interior use only: coves, cabinets, closets. For bathrooms, undercounter areas near sinks, and covered exterior details, step up to IP65, which resists dust and water jets. Fully exposed outdoor and washdown applications call for IP67 encapsulated tape. Remember the connectors and driver enclosure must match the rating, or the weakest link sets the real protection level.

Tape light usually illuminates the things people look at up close: countertops, merchandise, display shelves. CRI 90 or higher renders food, fabric, and finishes accurately, while low CRI tape makes the same materials look flat or off-color. The cost difference between CRI 80 and CRI 90 tape is small compared to the visual difference on the surfaces it lights.

For any permanent installation, channel is worth it. Aluminum channel acts as a heat sink that extends LED life, protects the tape from contact and dust, and its diffuser lens hides the individual LED dots for a continuous line of light. Surface, recessed, and corner profiles cover the common millwork details. Bare tape is acceptable inside enclosed coves where nothing touches it.